If you examine that flat area, you will notice that it is an integral machined part of the cross guard. This fit helps stabilize the bayonet and keep it from rotating around the axis of the barrel. NOTE: Of special interest it the way the small flat area behind the bayonet muzzle ring fits into the front of the cleaning rod bracket under the front sight base on the rifle. This again shows the interchangeability of Kalashnikov weapons system. Pictures are of a stripped Romanian 6X3 Type I bayonet and Egyptian made DDR AKM clone. A redesigned hanger was also developed with a snap hook to allow the scabbard to be detached for use as a wire cutter. With plastic like insulating grips on the hilt and a rubber insulator on the scabbard even electrically charged wire could be safely cut. This design also incorporated a means to connect with the scabbard to form a wire cutter. The first model bayonet designed for the AKM, (6X3 Type I), had the catch in the pommel and a muzzle ring as attachment points. Also with the new AKM a more conventional method of mounting a bayonet was introduced with a mounting stud under the front gas block. The main change to the rifle was the weight reduction and ease of production with the introduction of the stamped steel receiver replacing the forged and machined steel one on the AK47. MikeĮventually the AK47 was redesigned and upgraded and the AKM was introduced. I was using them to illustrate another post I am working on and they also represent the degree of interchangeability of all the ComBloc AK47 rifles and bayonets. The rifle pictured is a Chinese Type 56, (AK47) and the bayonet is a N. The first picture shows the required "fangs" on the bottom of the FSB. Maybe these pictures will help illustrate the means of attaching an AK47 bayonet to a rifle. Early production AK47 Rifles and various others where the fangs were omitted or removed to comply with import/export restrictions will not mount bayonets. The only change to the rifle was to add to small hooks, ("Fangs") to the bottom of the Front Sight Base. Ak 47 bayonet attached full#The cross guard incorporated a vertical sliding latch and a full muzzle ring. This was done by designing the rear of the pommel to fit around the Front Gas Block. These designs were not approved and it was decided that with the firepower, ease of rapid reloading and the overall compactness of the rifle that a bayonet was not needed.Īt some point this decision was reversed and a bayonet was retro designed to fit the rifle with minimal change to the rifle. Most of these were similar to and borrowed from existing Tokarev and Simonov bayonets and were conventional designs with the catch on the pommel engaging a flanged stud under the barrel. The four gas escape holes on the original AK-47s were omitted in favor of two gas relief holes on either side of the gas block. And, maybe surprisingly, the select fire options only included Safe and Semi-Automatic. Several different bayonet designs had been considered and several prototype and experimental bayonets can be found in reference books. The rear sights include graduations up to 1000 meters, as opposed to the 800 meter maximum found on a Soviet AK-47. Then again, your survival in the zombie-ridden wilderness of the end days is priceless.When the final design was approved and production was started on the original Russian AK47 rifles there was no means of mounting a bayonet. You can bet that if it does go up though, it’s going to cost a pretty penny. Doublestar’s previous effort, the DSC Zombie Slayer, sold for $1,249.99 but the Zombie X, for the moment, isn’t for sale. Whether or not that electric chainsaw really packs a punch or whether it’s really just a glorified hedgetrimmer is anyone’s guess, and as of now, you’ll have a hard time finding out. This particular model has a few other features as well, including a EOTech Zombie Stopper XPS2-Z Holographic Sight which gives you a biohazard sign instead of your normal crosshair another zombie apocalypse must. You do have an AK-47, don’t you? Ideally for use in the zombie apocalypse, the Doublestar Zombie X Chainsaw Rail Attachment is surprisingly quiet and runs on a stock-mounted battery rather than messy, flame-prone gasoline. The chainsaw bayonet, for instance, is a real thing, and while you won’t be able to mount it on a real Lancer, you can strap it to your AK-47. We still don’t have flying cars, but every day it seems like more and more sci-fi tech is getting defictionalized.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |